Header banner
Revain logoHome Page
Revainrating 5 out of 5

How to Measure, Install & Maintain A 15X25 Oval Overlap Liner For Above Ground Pools With Gasket Kit

How to Measure, Install & Maintain A 15X25 Oval Overlap Liner For Above Ground Pools With Gasket Kit

How to measure your above-ground pool to get the right size liner?

Getting the properly sized liner is crucial for your above-ground pool installation. An incorrectly sized liner can lead to folding, bunching up, and even tearing. Follow these steps to accurately measure your pool:

Materials Needed

  • Measuring tape
  • Pen and paper
  • 2 helpers

Measuring the Length and Width

First, measure the length and width across the top rails of your pool. Have one helper hold the zero end of the tape at one end while you walk the tape across to the far end. Record these measurements.

Measuring the Radius

For oval pools, you'll also need to measure the radius (distance from center to side) in a few spots and average them:

  1. Measure from pool center to both sides at each end.
  2. Measure from pool center to both sides halfway down the length.
  3. Average all radius measurements to get the overall radius.

Measuring the Wall Height

Finally, have a helper hold the end of the tape at ground level while you measure up the wall to the bottom of the top rail. Record the wall height.

Provide the length, width, radius, and wall height measurements to the liner manufacturer to get an accurately sized liner.

How to install an overlap pool liner for your above-ground pool?

Installing a new overlap liner for your above-ground pool properly ensures it fits snugly and lasts. Follow these key steps:

Materials Needed

  • New overlap pool liner
  • Liner adhesive
  • Gasket set
  • Scissors
  • Vacuum

Preparing the Pool

  1. Drain the pool and clean the walls thoroughly.
  2. Remove and set aside rails, filters, ladders, etc.
  3. Smooth out the sand bottom and remove any debris.

Installing the Liner

  1. Drape the liner over the wall with the printed side facing out.
  2. Lift the sides and push liner outward to flatten against the wall.
  3. Trim away excess material above the wall with scissors.
  4. Secure the liner to the top rail using liner adhesive.
  5. Install the gaskets behind the liner along the top rail.

Finishing Touches

  1. Reinstall ladders, rails, filters, etc.
  2. Start refilling the pool. Smooth out liner wrinkles.
  3. Once pool is 1/3 full, vacuum to adhere liner fully before continuing to fill.
  4. Trim any remaining excess liner material once pool is full.

Be sure to follow all safety guidelines when installing your new overlap pool liner.

How to cut the liner to fit your oval above-ground pool?

Cutting your oval pool liner to the proper shape and dimensions ensures a smooth installation and great fit. Follow these steps:

Materials Needed

  • Liner
  • Tape measure
  • Marker
  • Scissors or utility knife
  • Duct tape (optional)

Measure and Mark the Liner

  1. Lay the liner out flat on a clean surface like concrete or tarps.
  2. Measure the length and width per your pool's dimensions. Mark with duct tape or marker.
  3. For the radius, measure from the center point out to each side at a few points along the length. Average these to get the radius measurement.
  4. Use a marker and utility knife to trim along the tape edges to cut the liner to the proper rectangular dimensions.

Cutting the Oval Shape

  1. At each curved end, use your radius measurement to mark a half circle from the center point.
  2. Cut along the half circle lines with sharp scissors, being careful not to cut the main liner body.
  3. Trim off any excess material outside the half circles.

Tip for Liner Material

Overlap liners made of virgin vinyl materials cut best. Lower gauge 25-30 mil vinyl is easier to cut and install versus heavier 20 mil liners.

Taking time to properly measure and cut your oval pool liner results in a smooth installation and great fit with minimal folding or bunching up.

How to attach the liner to the pool wall and secure it?

Properly attaching and securing your pool liner ensures it stays in place. Follow these key steps:

Materials Needed

  • Pool liner
  • Liner adhesive
  • Liner locking strips
  • Scissors

Preparing the Liner

  1. Drape liner over pool wall, smoothing out wrinkles.
  2. Pull liner toward center to remove slack and create a smooth fit.
  3. Trim any excess liner material above the top rail.

Applying Adhesive

  1. Run a bead of liner adhesive along the underside of the pool top rail.
  2. Fold the liner over the top rail and press down firmly to adhere it to the rail and adhesive.
  3. Apply adhesive up the wall above the liner, then fold liner over and smooth down.

Installing Locking Strips

  1. Place locking strips over the liner where it folds over the top rail.
  2. Use a liner tool or screwdriver to press the locking strips down tightly.
  3. Trim any excess strip material hanging below the top rail.

Finishing Touches

  1. Make sure liner is adhered evenly around the entire perimeter.
  2. Smooth out any remaining wrinkles by pulling and refolding the liner as needed.

Taking care to properly attach all around the top ensures your pool liner stays securely in place.

How to use the gasket kit included with the liner?

Properly installing the gasket kit ensures a watertight seal between the liner and pool wall. Here are the key steps:

Gasket Kit Contents

  • Gasket sections
  • 2-sided gasket tape
  • Seam tape
  • Adhesive

Sizing the Gaskets

  1. Measure around the top rail of the pool wall.
  2. Cut the gasket sections to match this length when pieced together.

Installing the Gaskets

  1. Clean the top rail surface thoroughly where gaskets will be placed.
  2. Apply the 2-sided gasket tape to the back of the gasket sections.
  3. Remove backing paper and press gaskets firmly onto the top rail behind the liner overlap.

Sealing the Seams

  1. Use seam tape at the joints where gasket sections meet.
  2. Run a bead of adhesive along all seams and rub smooth.
  3. This seals the gasket pieces into one continuous gasket.

Checking for Gaps

  1. Visually inspect the gasket installation and test for any remaining gaps.
  2. Reseal any gaps with additional adhesive to prevent future leakage issues.

Properly installing the included gasket kit creates a continuous seal and prevents water from getting behind the liner.

How to maintain and clean an overlap pool liner?

Proper care and cleaning are key to preventing algae growth and extending the life of your overlap pool liner. Follow these maintenance tips:

Weekly Maintenance

  • Brush walls thoroughly to prevent buildup.
  • Check liner for signs of damage or wear.
  • Clean all surfaces with pool skimmer.

Monthly Maintenance

  • Shock treat the pool water to prevent algae growth.
  • Inspect liner seams and gaskets for gaps or detachment.
  • Drain water level down halfway and scrub liner with brush.

Cleaning Liner Stains

  1. Try removing minor stains with a vinyl liner cleaner product.
  2. For tougher rust or calcium stains, use a diluted muriatic acid solution.
  3. Rinse cleaned areas thoroughly before refilling pool.

Tip for Water Level

Keeping pool water level 6-12 inches below top rail takes pressure off the liner and can help prevent premature wear or detachment.

Replacing Liner

Plan to replace the entire liner every 5-7 years as exposure to sun and pool chemicals cause wear over time.

With regular care and cleaning, your overlap pool liner should stay in great shape each swim season.

How to get an Amazon Prime subscription profitably when buying the pool liner

Amazon Prime can be a great way to save on shipping costs and get access to streaming services when purchasing the 15x25 oval overlap pool liner. Here are some tips to get Prime in a cost-effective way:

Sign Up for a Free Trial

If you don't already have a Prime membership, sign up for the 30-day free trial. This allows you to enjoy Prime benefits like free 2-day shipping when ordering the liner.

Compare Retailer Prices

Even with free shipping, check that Amazon's price on the liner is competitive or lower than other major retailers. The savings from Prime shipping need to outweigh any difference in the item price.

Use an Amazon Prime Rewards Card

Sign up for an Amazon Prime Rewards Visa and get a $100 gift card upon approval. Use this towards your liner purchase to offset the $139 Prime membership fee.

Split the Membership

If you split the Prime membership with a friend or family member, the $139 annual fee becomes more affordable at just $70 each.

Check for Discounts

Some customers can get Prime discounts through government assistance programs or student offers. Check if these savings apply to you.

Using these tips can help you profit from an Amazon Prime membership when purchasing big-ticket items like the pool liner.

Top of our users