Header banner
Revain logoHome Page
Revainrating 4 out of 5

Restore Lost Power and Improve High Mileage Engine Performance with Rislone Engine Treatment

Restore Lost Power and Improve High Mileage Engine Performance with Rislone Engine Treatment

How to improve engine performance in high mileage vehicles?

As vehicles accumulate miles, engine performance can suffer from loss of compression, clogged fuel injectors, contaminated oil, and sludge build-up. Fortunately, there are steps you can take to restore power and improve efficiency in high mileage engines:

Use Fuel Injector Cleaner

Over time fuel injectors get clogged with deposits that restrict fuel flow. By using a fuel injector cleaner regularly, you can remove these deposits and improve fuel atomization for better combustion:

  • Add bottle of fuel injector cleaner to gas tank once every 3,000 miles
  • Drive normally for a few days to circulate cleaner through the fuel system
  • Repeat process 2-3 times per year

Change Oil Regularly

Dirty oil can cause sludge build-up and engine wear. Follow the manufacturer's recommendations for oil change frequency:

  • Use oil viscosity recommended in owner's manual
  • Replace oil filter with each oil change
  • Consider using high mileage motor oil

Use Engine Treatments

Detergent compounds in engine treatments can dissolve sludge, reduce friction, and replenish oil additives to improve performance:

  • Add engine treatment to crankcase with each oil change
  • Let idle for 10-15 minutes after adding to circulate
  • Treatments with PTFE can also quiet noisy lifters and rings

Following these best practices for high mileage engine care can restore lost power and keep your vehicle running smoothly.

How to reduce oil consumption in older engines?

It's common for older engines to burn more oil as they accumulate mileage. But excess oil consumption can be reduced through proper maintenance and repair:

Use Thicker Oil

Switching to a higher viscosity oil can help seal worn piston rings and bearings to reduce oil slipping by:

  • Consult owner's manual for recommended viscosities
  • Choose 5W grades instead of 0W grades (like 5W-30 instead of 0W-30)
  • Avoid exceeding maximum viscosity recommended

Replace PCV Valve

A faulty PCV valve can draw too much oil into the engine causing burn off:

  • Locate PCV valve on valve cover or intake manifold
  • Remove old valve and install new replacement
  • Use OEM part or high quality aftermarket PCV valve

Use Oil Additives

Oil additives with seal conditioners can recondition aged seals and gaskets:

  • Look for additives with PTFE or ester oils
  • Follow directions to add to crankcase before oil change
  • Allows time to circulate before draining old oil

Fix External Leaks

Identify and repair any external leaks that could be reducing oil level:

  • Inspect valve covers, oil pan, seals for leaks
  • Replace cracked/damaged gaskets or seals
  • Monitor oil level frequently after repairs

Addressing mechanical issues promptly can help reduce oil consumption in high mileage engines.

How to restore lost power and acceleration?

Over time, engine power and acceleration can decline due to carbon deposits, worn rings, and low compression. Here are some tips to restore performance:

Clean Fuel Injectors

Dirty injectors can reduce power and cause poor acceleration:

  • Use a high quality fuel injector cleaner product
  • Add to fuel tank at least once every 10,000 miles
  • Drive normally for a few days to circulate cleaner

Change Ignition System Parts

Worn spark plugs and coils weaken combustion:

  • Replace spark plugs and inspect plug wires
  • If over 100k miles, install new coil pack
  • Check for faulty ignition control module

Use Fuel System Cleaner

Cleans injectors, valves, chambers:

  • Add fuel system cleaner to empty tank
  • Refill with fresh gasoline
  • Drive to circulate through fuel system

Clean Intake Valves

Carbon buildup on valves reduces air flow:

  • Use intake valve cleaner spray per instructions
  • Removes deposits without disassembly
  • Perform every 15,000 miles for preventive maintenance

Following a tune-up schedule and using quality fuel additives can help restore lost engine performance over time.

How to prolong engine life?

Taking proper care of your engine is key to prolonging its life and minimizing major repairs down the road. Here are some best practices:

Regular Oil Changes

Dirty oil can cause premature wear and sludge build-up:

  • Change oil based on mileage, not months
  • Use oil viscosity recommended by manufacturer
  • Inspect oil at changes - gray or black indicates frequent changes needed

Quality Fuel

Poor quality or dirty fuel can clog injectors and damage cylinders:

  • Purchase gasoline from busy stations to avoid old gas
  • Use top tier detergent gasoline when available
  • Consider fuel injector cleaners periodically


Replacing worn parts prevents further damage:

  • Follow factory advise on spark plug and wire replacement
  • Inspect and test coils, caps, rotors per maintenance schedule
  • Replace air filter as needed or every 20,000 miles

Drive Carefully

Aggressive driving causes more wear:

  • Allow engine to warm up before high revs
  • Avoid revving engine excessively
  • Drive at moderate speeds and accelerate gradually

Making smart maintenance choices and driving with care can add years of life to your engine.

How To Use High Mileage Engine Treatment For Your Vehicle?

Here are the steps on how to use High Mileage Engine Treatment for your vehicle:

  1. Determine the oil capacity of your engine. For passenger car and light truck engines, use one bottle of Rislone Engine Treatment for a 4 to 6 quart system. For larger systems, add one bottle for every 5 quarts of capacity.
  2. Add the entire bottle of High Mileage Engine Treatment to the engine crankcase.
  3. High Mileage Engine Treatment may be used anytime, at or between oil changes. For best protection, use High Mileage Engine Treatment at every oil change.
  4. For severely dirty engines, use two bottles of High Mileage Engine Treatment and change the oil after 100 miles of driving.
  5. Remove the oil filler cap and pour the recommended amount of High Mileage Engine Treatment.
  6. Simply pour High Mileage in your fuel tank and oil crankcase to clean and lubricate critical engine areas and help keep your higher mileage vehicle on the road.

How Often Should You Use High Mileage Engine Treatment?

The frequency of using High Mileage Engine Treatment depends on the age and condition of your vehicle. Ideally, High Mileage Engine Treatment can be used at every oil change to provide the best protection for your engine. However, if your engine is severely dirty, you can use two bottles of High Mileage Engine Treatment and change the oil after 100 miles of driving. If you have a high mileage vehicle that has been well maintained and are attempting to mitigate more engine wear with realistic expectations, a high mileage engine oil might be the right choice for you. It is important to note that High Mileage Engine Treatment is not a "silver bullet" for mechanical wear in your engine.

What Are The Benefits Of Using High Mileage Engine Treatment?

Using High Mileage Engine Treatment can provide several benefits to your vehicle, especially if it has over 75,000 miles or more. Here are some of the benefits of using High Mileage Engine Treatment:

  • Prevents oil leaks by conditioning engine seals that may have degraded over time
  • Reduces oil consumption and burn-off
  • Breaks up and dissolves sludge left behind by other oils
  • Reduces general wear and tear on older engines
  • Improves fuel efficiency
  • Soothes cracked and brittle engine pieces, adding a boost of flexibility to the parts that need it most
  • High Mileage Engine Treatment is infused with a unique blend of conditioning agents and additives that regular oil doesn't have. It can help rejuvenate engines that are worn down and keep them performing efficiently for longer. While High Mileage Engine Treatment can provide several benefits, it is important to note that it is not a "silver bullet" for mechanical wear in your engine.